Aller au contenu principal
  • Paul Scherrer Institut PSI
  • PSI Research, Labs & User Services

Digital User Office

  • Digital User Office
  • DE
  • EN
  • FR
Paul Scherrer Institut (PSI)
Rechercher
Paul Scherrer Institut (PSI)

Hauptnavigation

  • Research at PSIOuvrir ce point de menu principal
    • Research Initiatives
    • Ethics and Research integrity
    • Scientific Highlights
    • Scientific Events
    • Scientific Career
    • PSI-FELLOW
    • PSI Data Policy
  • Research Divisions and LabsOuvrir ce point de menu principal
    • Overview
    • Research with Neutrons and Muons
    • Photon Science
    • Energy and Environment
    • Nuclear Energy and Safety
    • Biology and Chemistry
    • Scientific Computing, Theory and Data
    • Large Research Facilities
  • Facilities and InstrumentsOuvrir ce point de menu principal
    • Overview
    • Large Research Facilities
    • Facilities
    • PSI Facility Newsletter
  • PSI User ServicesOuvrir ce point de menu principal
    • User Office
    • Methods at the PSI User Facilities
    • Proposals for beam time
    • Proposal Deadlines
    • Data Analysis Service (PSD)
    • EU support programmes
  • New ProjectsOuvrir ce point de menu principal
    • SLS 2.0
    • IMPACT
  • DE
  • EN
  • FR

Digital User Office (mobile)

  • Digital User Office

Vous êtes ici:

  1. PSI Home
  2. Labs & User Services
  3. NUM
  4. SINQ
  5. POLDI
  6. Description
  7. Sample Environments
  8. Uniaxial load frame

Navigation secondaire

POLDI

  • Description Sous-menu élargi
    • Basic principle
    • Components
    • Parameters
    • Sample Environments Sous-menu élargi
      • Sample table
      • Uniaxial load frame
      • Multiaxial load frame
      • Furnace
      • Cryostat
  • User Information
    • Schedule
    • Data Analysis
  • Publications
  • People
  • Safety

Info message

Ce contenu n'est pas disponible en français.

Overview

The POLDI load frame has a load capacity of maximal 30 kN. Measurements in horizontal and vertical position (figure 1) are possible. This allows measuring the lattice strain evolution both parallel and perpendicular to the tensile axis (axial and transverse strains).

Load frame positioned horizontally.
Load frame positioned horizontally.

Neutron collection can be performed under constant load or constant displacement conditions, or a combination of both.

Sample geometry

Several samples geometries are possible:

Flat (maximum 10kN)

The deformation rig is equiped with Mark-10 Test Grips (Dynamic Measurement Systems LLC, G1012-1) for mounting flat specimens (see for instance figure 2, technical drawing). For measurements in horizontal position a minimum gauge length of 44mm is recommended (for samples with shorter gauge length the diffracted neutron beam might be partly shadowed by the tensile grips).

Round (maximum 30kN)

The tensile rig supports M6 (technical drawing) and M12 (technical drawing, or for fatigue): Example of a round fatigue specimen with M12 thread.) threaded tensile specimens, as shown in figures 3 and 4, respectively. The gauge length of the specimens shown in these figures are minimum values only. To determine the appropriate sample geometry take following considerations into account:

  • One cannot exceeded the maximum force of 30kN
  • Ideally the gage volume sampled by neutrons should be fully immersed in the sample. For instance, for the combination of a 2mm wide incoming beam and the 1.5mm radial collimator the minimum sample diameter would be 2.5mm.
  • In case the strain is measured with an axial extensometer take into account that possible gauge lengths and travel ranges are restricted (see below).

For other types of specimens (such as wires, compression samples, ...) contact one of the beamline scientists

Figure 2
Figure 2
Figure 3
Figure 3
Figure 4
Figure 4
Figure 5
Figure 5

Strain measurement

Currently three methods for strain measurements are available:

Clip-on axial extensometer

Two high precision axial extensometers are available. The properties are given in the following table. Both extensometers can be used for the sample geometries listed above.

Type Gage length Maximum travel Maximum strain Data sheet
MTS 634.12F-25 25 mm* +12.5mm / -2.5mm +50% / -10% Data sheet (external link)
MTS 632.26F-20 8 mm +/-1.2mm +/-15%  

* A gage length extender up to 50mm is also available.

Strain-gaged flexures

Strain-gage flexure attached to the sample can be read out using the NI USB-9219 Universal Analog Input Module. Quarter, half, and full-bridge gages can be used. Note that strain gaged flexures are not available at the beam line and should be mounted by the user before the start of the experiment.

Optical digital camera

The tensile rig is equiped with a NI 1764 Smart Camera. Strain measurements can be performed by measuring the distance between two markers or by image correlation. Contact the instruments responsibles to find out which solution is appropriate for your samples.

Sidebar

Contact

Instrument responsible
Dr. Efthymios Polatidis
Phone: +41 56 310 3948
E-mail: efthymios.polatidis@psi.ch

Instrument co-responsible
Steven Van Petegem
Phone: +41 56 310 2537
E-mail: steven.vanpetegem@psi.ch

Organization

  • LNS Groups
  • LNS Home
  • NUM Division

SINQ Facility

Read about the accelerator and target station of the Neutron Source facility

SINQ Sample Environment

Get full information on the SINQ sample environment

Open Positions

  • SINQ open positions
  • Open positions in the Division NUM
top

Pied de page

Paul Scherrer Institut

Forschungsstrasse 111
5232 Villigen PSI
Suisse

Téléphone: +41 56 310 21 11
Téléfax: +41 56 310 21 99

Comment nous trouver 
Contact

Centre de visiteurs psi forum
Laboratoire élèves iLab (en allemand)
Centre de protonthérapie
Centre de Formation du PSI
PSI Guest House (en anglais)
PSI Gastronomie (en allemand)
psi forum shop

Service & Support

  • Annuaire
  • User Office
  • Accelerator Status
  • Publications du PSI
  • Fournisseurs
  • E-facture
  • Computing (en anglais)
  • Sicherheit (en allemand)

Carrière

  • Travailler au PSI
  • Offres d'emploi
  • Formation initiale et formation continue
  • Career Center
  • Formation professionnelle (en allemand)
  • Centre de Formation du PSI

Pour les médias

  • Le PSI en bref
  • Chiffres et faits
  • Le coin médias
  • Communiqués de presse
  • Réseaux sociaux

Suivez le PSI: Twitter (in English) LinkedIn Youtube Facebook Instagram Issuu RSS

Footer legal

  • Impressum
  • Conditions d'utilisation
  • Login éditeurs